APRS-MX Track Direct

☰

reset

SQ9PQL-00 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9PQL-00. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TX*	RX*	Digi*
1794260298	271 Count	156 Count	149 Count
1794259394	269 Count	155 Count	148 Count
1794258490	267 Count	154 Count	147 Count
1794257586	265 Count	153 Count	146 Count
1794256683	263 Count	152 Count	145 Count
1794255779	261 Count	151 Count	144 Count
1794254875	259 Count	150 Count	143 Count
1794253971	257 Count	149 Count	142 Count
1794253068	255 Count	148 Count	141 Count
1794252164	253 Count	147 Count	140 Count
1794251260	251 Count	146 Count	139 Count
1794250356	249 Count	145 Count	138 Count
1794249453	247 Count	144 Count	137 Count
1794248549	245 Count	143 Count	136 Count
1794247645	243 Count	142 Count	135 Count
1794246741	241 Count	141 Count	134 Count
1794245837	239 Count	140 Count	133 Count
1794244934	237 Count	139 Count	132 Count
1794244030	235 Count	138 Count	131 Count
1794243126	233 Count	137 Count	130 Count
1794242222	222 Count	127 Count	120 Count
1794241319	212 Count	118 Count	111 Count
1794240415	210 Count	117 Count	110 Count
1794239511	208 Count	116 Count	109 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by Homero Lozano, XE2KK, based on APRS Track Direct