APRS-MX Track Direct

☰

reset

LW2DHT-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LW2DHT-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX*	RX*	Digi*
1794248586	99 Count	125 Count	83 Count
1794246783	93 Count	119 Count	78 Count
1794244980	80 Count	100 Count	66 Count
1794243177	57 Count	69 Count	44 Count
1794241374	52 Count	61 Count	40 Count
1794239571	46 Count	54 Count	35 Count
1794237768	40 Count	48 Count	30 Count
1794235965	34 Count	42 Count	25 Count
1794234161	28 Count	36 Count	20 Count
1794232358	23 Count	29 Count	16 Count
1794228784	9 Count	15 Count	8 Count
1794226983	4 Count	8 Count	4 Count
1794225179	782 Count	1001 Count	587 Count
1794223376	776 Count	995 Count	582 Count
1794221573	770 Count	988 Count	577 Count
1794219770	764 Count	981 Count	572 Count
1794217967	758 Count	975 Count	567 Count
1794216164	752 Count	969 Count	562 Count
1794214359	746 Count	963 Count	557 Count
1794212555	740 Count	957 Count	552 Count
1794210755	735 Count	952 Count	548 Count
1794207185	721 Count	942 Count	540 Count
1794205381	716 Count	937 Count	536 Count
1794203578	696 Count	917 Count	517 Count
1794199972	672 Count	892 Count	495 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by Homero Lozano, XE2KK, based on APRS Track Direct