This is the latest recevied telemetry packets stored in our database for station/object SP2WM-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1794247608 | 348 Count | 597 Count | 199 Count | 0 VDC | 0 VDC |
| 1794246707 | 345 Count | 593 Count | 197 Count | 0 VDC | 0 VDC |
| 1794245806 | 344 Count | 591 Count | 197 Count | 0 VDC | 0 VDC |
| 1794244905 | 342 Count | 587 Count | 196 Count | 0 VDC | 0 VDC |
| 1794244004 | 339 Count | 584 Count | 194 Count | 0 VDC | 0 VDC |
| 1794243104 | 337 Count | 582 Count | 193 Count | 0 VDC | 0 VDC |
| 1794242203 | 335 Count | 581 Count | 192 Count | 0 VDC | 0 VDC |
| 1794241302 | 331 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794240401 | 330 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794239501 | 329 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794238600 | 328 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794237699 | 327 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794236799 | 326 Count | 578 Count | 189 Count | 0 VDC | 0 VDC |
| 1794235897 | 323 Count | 573 Count | 187 Count | 0 VDC | 0 VDC |
| 1794234997 | 320 Count | 567 Count | 185 Count | 0 VDC | 0 VDC |
| 1794234096 | 315 Count | 557 Count | 181 Count | 0 VDC | 0 VDC |
| 1794232294 | 307 Count | 525 Count | 175 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)