APRS-MX Track Direct

☰

reset

SQ9IKM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9IKM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX*	RX*	Digi*
1794247097	189 Count	530 Count	144 Count
1794246196	186 Count	523 Count	142 Count
1794245296	183 Count	514 Count	140 Count
1794244395	180 Count	506 Count	138 Count
1794243494	176 Count	498 Count	136 Count
1794242593	173 Count	491 Count	134 Count
1794241693	163 Count	474 Count	125 Count
1794240792	155 Count	458 Count	118 Count
1794239891	151 Count	448 Count	115 Count
1794238991	148 Count	441 Count	113 Count
1794238090	141 Count	426 Count	108 Count
1794237204	139 Count	420 Count	107 Count
1794236303	136 Count	412 Count	105 Count
1794235403	132 Count	400 Count	102 Count
1794234502	128 Count	385 Count	99 Count
1794233601	123 Count	374 Count	95 Count
1794232701	120 Count	365 Count	93 Count
1794231800	117 Count	359 Count	91 Count
1794230899	108 Count	344 Count	83 Count
1794229999	106 Count	338 Count	82 Count
1794229098	103 Count	332 Count	80 Count
1794228197	100 Count	325 Count	78 Count
1794227297	98 Count	313 Count	77 Count
1794226396	94 Count	305 Count	74 Count
1794225496	91 Count	297 Count	72 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time:

Maintained by Homero Lozano, XE2KK, based on APRS Track Direct